DoRevision

Timing Circuits: RC Networks and the 555 Timer

How a capacitor filling through a resistor makes a time delay: charging and discharging curves, changing the delay with R and C, the 555 monostable and astable, their equations, and reading the output on an oscilloscope.

⏱️ 22 min 🎯 17 activities
Best used for
Independent study Mock preparation Cover lesson

Get the method right under pressure

Free interactive practice on the steps that lose marks under exam pressure.

Start revising free

What you'll cover

A timer is a capacitor filling up

Every timing circuit in this topic works the same way underneath. A capacitor fills with charge through a resistor, and its voltage climbs. Something else in the circuit watches that voltage, and when it gets high enough, the output changes. The wait between the start and that moment is the time delay. That idea is all there is to a simple RC network, a resistor and capacitor joined in series across a supply, with a transistor or comparator switching on once the capacitor voltage is high enough. It is also the idea inside the 555 timer, an eight-pin chip that has the watcher built in and can be wired two ways: as a monostable that gives one timed pulse, or as an astable that keeps on pulsing. So whenever you meet a timing question, ask the same three things. What is filling, and through what? What voltage is being watched for? And what would make the filling slower or faster? This module works through the charging curve, the two 555 circuits and their equations, and how to read a timer output on an oscilloscope.

Timing circuit words

Learn these before you work any timer. Keep monostable and astable apart: one waits for you, the other never stops.

Match each timing job to the circuit that does it

  • A stairwell light that stays on for two minutes after one press of a button
  • A bike light that flashes on and off until someone switches it off
  • An alarm that waits a few seconds before sounding, made only from a resistor, a capacitor and a transistor
  • Checking how long each flash of a flashing circuit lasts
  • a 555 wired so that one press gives one fixed-length burst of output
  • a 555 wired to run free, pulsing for as long as it has power
  • a slow-filling capacitor that holds the switch off until its voltage is high enough
  • an oscilloscope, which draws the output against time so the pulses can be measured

Swap the resistor

An RC delay uses a 10 kilohm resistor. The designer swaps it for a 47 kilohm resistor and keeps the same capacitor. What happens to the delay?

  • It becomes about 4.7 times as long, because less current flows to fill the capacitor
  • It becomes shorter, because a bigger resistor pushes the charge in harder
  • It stays the same, because only the capacitor sets the delay
  • It becomes exactly 37 seconds longer, the difference between the two resistors

Reading a charging curve

This is what the voltage across a capacitor does over time. When charging starts, the capacitor is empty, so the whole supply voltage sits across the resistor and a large current flows in. The voltage therefore rises fastest at the start. As the capacitor fills, its own voltage pushes back against the supply. Less voltage is left across the resistor, so less current flows, and the voltage climbs more and more slowly. The curve bends over and creeps up towards the supply voltage, getting very close but in theory never quite reaching it. Discharging is the mirror image, called a decay curve. A full capacitor pushes a large current out through the resistor at first, so the voltage falls fastest at the start, then the fall slows and the curve tails off towards zero. Either way, the steep part is at the beginning and the flat part is at the end.

How R and C set the delay

The delay depends on two components, and each one slows the filling in its own way. A larger resistance lets less current through, so charge arrives more slowly. A larger capacitance needs more charge before its voltage rises by the same amount. Either change makes the delay longer. What matters is R multiplied by C. That product sets the time scale of the whole curve, so the delay is in proportion to both: double the resistance and the delay doubles, double the capacitance and it doubles too, and double one while halving the other and nothing changes at all. On a voltage-time graph a longer delay shows as a stretched curve, gentler and slower to reach the watched voltage. Inside a 555 the watcher is built in: in a monostable it waits for the capacitor to reach two-thirds of the supply. Stretch the curve of an astable and every cycle takes longer, so the pulses come less often.

Find the fastest charging

This graph shows a capacitor charging and then discharging. Tap the part of the curve where the capacitor voltage is RISING most quickly.

Halve the capacitor

An RC delay lasts 8 seconds. Its 100 microfarad capacitor is replaced with a 50 microfarad one, and the resistor stays the same. Choose the words that complete the result.

Monostable against astable

The same 555 chip, wired two ways. The difference is whether the circuit has somewhere to rest. For any repeating output, frequency is one divided by the period, the time for one whole cycle.

Work out the pulse length

A 555 monostable uses a 100 kilohm resistor and a 100 microfarad capacitor. Work out its pulse duration in seconds.

Order one monostable pulse

Put the events of one 555 monostable pulse in order, earliest first.

  • A brief low pulse arrives at the trigger input
  • The output switches high and the capacitor starts charging through the resistor
  • The capacitor voltage climbs to two-thirds of the supply
  • The output drops low and the capacitor is emptied quickly
  • The circuit sits with its output low, ready for the next trigger

Reading the output on an oscilloscope

Picture the output of an astable on an oscilloscope screen: a row of flat-topped pulses on a grid of squares. Two dials matter. The time base says how much time each square across stands for, and the volts setting says how many volts each square up stands for. To find the period, count the squares across one whole cycle, from the start of one pulse to the start of the next, so one mark and one space together. Multiply that count by the time base. The frequency is then one divided by the period, so check the units: milliseconds give a period that must be turned into seconds before you divide. To find the amplitude, count the squares from the zero line up to the flat top of a pulse and multiply by the volts setting. You can also count the mark and the space separately, which lets you check the mark-space ratio against the resistor values.

Read the oscilloscope trace

An astable output is on an oscilloscope. The time base is 5 milliseconds per square and the volts setting is 2 volts per square. One whole cycle spans 4 squares across, so the period is _____ milliseconds and the frequency is _____ hertz. Each pulse rises 2.5 squares above the zero line, so the amplitude is _____ volts.

20 50 5 9 1.25 0.2 500

Lower the flashing rate

A 555 astable flashes an LED too quickly. Select the TWO changes that would LOWER its frequency.

  • Use a capacitor with a larger value
  • Use a larger resistor for R2
  • Use a smaller resistor for R1
  • Use a capacitor with a smaller value

The 555 calculation run

Five quick 555 calculations. Three lives.

Design the timer

You are designing timers for a school. Work through three decisions.

  • A corridor light must come on when a button is pressed and switch itself off after a set time. Which 555 circuit fits?
  • Built and tested, the light stays on for 15 seconds, but the brief says 30. Which change fixes it?
  • Next, a warning lamp built on an astable must stay on far longer than it stays off in each flash. Which choice does that?

Slow the bike light down

A classmate has built a 555 astable for a bike light. It flashes too fast, and the light is on for only a little longer than it is off. Explain to them how the circuit times itself and what to change.

  • The capacitor charging and discharging
  • What sets the mark and the space
  • A change that lowers the frequency
  • A change that lengthens the on-time
  • How an oscilloscope would confirm it